Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Highland Creek Homeowners
Most chimney problems we’re called out to in Highland Creek start small and stay quiet: a hairline crack in the crown, a few crumbling mortar joints, a flash of white staining on the brick after a wet winter. Left alone, each one gives water another way in, and water is what turns a cheap repair into a rebuild. Our technicians have up to 13 years of experience diagnosing exactly that kind of damage, and we fix it with professional-grade materials from makers like HeatShield and Olympia Chimney rather than a patch that fails by the next cold snap.
We handle the whole chimney system here: mortar work, waterproofing, flashing, liners and structural rebuilds, all through one relationship instead of three separate contractors. If you’re seeing something that worries you, call (855) 337-1327 for a free estimate. We answer 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday.
What Our Chimney Repair Service Includes
Chimney repair isn’t one trade. Masonry, water management and the flue itself all fail in different ways, and the fix has to match the failure. Here’s what each piece of the work actually involves.
Mortar Repointing
Repointing is replacing the mortar between bricks once it has eroded, cracked or turned to powder, and it’s the most common repair we make on older Highland Creek chimneys. You need it when joints are recessed more than a fraction of an inch or crumble when you touch them, because that’s when water starts finding the brick face instead of the joint. We grind out the failed mortar to a proper depth and pack in fresh material matched to the existing color and hardness, so the repair doesn’t blow out the softer brick around it.
Spalling Brick Repair
Spalling is when the face of a brick flakes off, pits or peels away in layers, usually after moisture gets in and freezes. It signals bricks that are saturated and no longer shedding water, and it tends to spread upward and outward if the source of the moisture isn’t addressed. We replace the failed units with matching brick, then deal with the reason they failed, which is often a bad crown or missing cap rather than the brick itself.
Chimney Waterproofing
Waterproofing is a breathable sealer applied to the masonry that stops liquid water from soaking in while still letting the chimney dry from the inside out. You need it after any masonry repair, and on any chimney that shows white salt staining, dark damp patches or moss on the north side. We use vapor-permeable products so trapped moisture can escape, because a sealer that traps water does more damage than no sealer at all.
Flashing Repair
Flashing is the metal where the chimney meets the roof, and it’s the single most common source of chimney leaks we find. It needs attention when you see rust, lifting edges, cracked tar around the base, or staining on the ceiling below. We rebuild the flashing layers with proper counter-flashing and sealant details from Famco and Copperfield, because a smear of caulk over a failing joint never holds through a full year of weather.
Chimney Rebuilding
Rebuilding is taking a chimney down to a sound course of brick and building it back up, and it’s the right call when the structure has leaned, the top courses are loose, or repointing can no longer hold the stack together. It becomes necessary after long-term water damage, freeze-thaw movement or a chimney fire that cracked the inner wythes. We rebuild from the roofline up to the correct height for the flue, then cap and waterproof it so the new work lasts.
Tuckpointing
Tuckpointing is the finer version of repointing: cutting out old mortar and filling it with a slightly recessed or contrasting finish for a neater, more uniform face. It’s chosen when the masonry is structurally sound but the joints look ragged, or when a homeowner wants a clean appearance on a visible chimney. We treat it as a masonry finish, not a cosmetic cover-up, so the joints underneath still do their job.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
Repair quality depends heavily on what goes into the chimney, which is why we work with products the trade actually trusts. HeatShield is a ceramic repair system for fireboxes and flue interiors, and we use it where resurfacing can restore a sound flue without tearing out a liner that still has life in it. It’s a repair that many sweep-only companies simply don’t offer, and it’s often the difference between a few hundred dollars and a full reline.
DuraFlex flexible liner systems cover wood, gas and oil appliances, and we specify them when a flue needs relining after a crack, a chimney fire or a flue that was never sized correctly. Olympia Chimney components show up in our cap and top-of-stack work, where the right fit matters more than people expect. And whether your chimney has Olympia Chimney, Famco, Copperfield, DuraFlex or any other make on it, we can help, because the diagnosis drives the material, not the other way around.
Signs You Need Chimney Repair Right Now
Some of these can wait a few weeks. Some shouldn’t. Here’s how to tell what you’re looking at before you call anyone.
- Cracked or crumbling mortar joints. If the mortar between bricks is recessed, sandy or falling out in pieces, water is already getting behind the brick face. Repointing early is a modest masonry job; ignoring it usually leads to spalling brick and, eventually, a rebuild.
- White staining or dark damp patches on the brick. That chalky white bloom is salt drawn out by moisture moving through the masonry, and dark patches mean the brick is holding water. Both point to a waterproofing or flashing problem rather than dirt, and both get worse each freeze-thaw cycle.
- Rust, gaps or cracked sealant where the chimney meets the roof. This is the flashing, and it’s the most frequent cause of chimney leaks. A stain on the ceiling or a drip in the attic after heavy rain is often the first sign you’ll see inside the house.
- A leaning or visibly damaged chimney stack. Movement in the structure, loose bricks near the top or a crown that has separated from the flue are all reasons to stop using the fireplace until it’s assessed. This is the point where rebuilding is usually cheaper than repeated patching.
- Loose or missing chimney cap and a failing crown. A crown that’s cracked lets water straight into the top of the chimney, and a missing cap lets rain and animals in from above. Both are quick repairs that protect everything underneath them.
Our Chimney Repair Process – Step by Step
- 1
We start with a camera inspection. Before anyone quotes a repair, we run a camera through the flue and photograph the firebox, damper and smoke chamber. You see the same images we do, so the recommendation isn’t something you have to take on faith.
- 2
We explain what we found and what it means. We walk you through each issue, how serious it is, and whether it’s a now problem or a later problem. If work can safely wait a season, we say so plainly.
- 3
You get a written, flat-price estimate. The estimate covers the scope we agreed on before booking, with materials listed. The price you see is the price for that job, and the written estimate is what sets the final figure.
- 4
We do the masonry and structural work. Repointing, brick replacement, flashing, crown and cap work all happen with materials matched to your chimney. Where resurfacing can solve a firebox or flue problem, we use HeatShield ceramic repair instead of defaulting to replacement.
- 5
We test and document the finished repair. We check that the flashing sheds water, the crown drains correctly and the flue is clear, then give you photos of the completed work. You know what was done and what it looks like, which matters if you ever sell the house.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Highland Creek?
Chimney repair in Highland Creek typically runs from about $250 for minor mortar or crown work up to several thousand dollars for a partial rebuild, depending on how much masonry is involved and how far the damage has spread. A typical mortar repointing job runs $350 – $900 depending on how many joints are being cut out and how high the work sits above the roofline. Waterproofing a standard chimney usually runs $300 – $600. Flashing repair tends to land between $400 and $900, since the job is as much about the roof seal as the metal. A chimney rebuild from the roofline up is the largest line item, generally $2,500 to $6,000 or more for a full stack, because it’s new masonry, a new crown and a cap all in one.
What moves the price is access and height, how many faces of the chimney are exposed, whether the damage is cosmetic or structural, and whether the flue needs any liner work alongside the masonry. You avoid overpaying by getting the inspection first and fixing the cause rather than the symptom; a waterproofed chimney with a sound crown stops the cycle that keeps creating repairs. Every estimate we give is free, itemized and flat-priced, and nothing gets recommended that you can’t see on camera yourself.
Chimney Repair Near Highland Creek – Our Service Area
We connect homeowners across the north Charlotte area with independent local chimney professionals, including Derita, NoDa, University City and Plaza Midwood, plus Elizabeth, Hickory Grove, Wesley Heights, Dilworth, Myers Park, Eastover and Mountain Island. Response windows depend on the day’s route and the scope of the work, but we book promptly and confirm your window when we schedule. For related work in nearby neighborhoods, see our chimney repair page for Derita and chimney repair for NoDa.
Serving Highland Creek, NC – Our Local Coverage Area
We serve Highland Creek and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Highland Creek
Chimney repair is fixing the structural and masonry parts of the chimney system: mortar joints, brick, the crown, flashing, waterproofing and the flue interior. It’s different from a cleaning, which removes creosote and soot but doesn’t address damage. We assess the whole system first, then repair what’s actually failing, and we handle the root cause rather than just the visible symptom.
Most repairs take a single visit, with repointing, flashing and crown work usually done in a few hours to a day. A full rebuild takes longer because the mortar needs time to cure between courses, often two to three days depending on weather. We give you a realistic timeline with the written estimate so you can plan around it.
It typically runs from about $250 for a small crown or mortar fix up to $6,000 or more for a full chimney rebuild, with repointing, waterproofing and flashing landing in between. The written estimate sets the final price, and the inspection is what determines which tier you’re in. Call (855) 337-1327 for an exact quote; estimates are free.
Yes, we work with Olympia Chimney components and DuraFlex liner systems, along with HeatShield ceramic repair, Famco and Copperfield flashing materials. We match the product to the repair rather than forcing one material onto every chimney. If your chimney has any of these brands, we can assess it.
Same-day repair is often possible when the work is straightforward and the schedule allows. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Call (855) 337-1327 and we’ll book you into the next opening.
Yes, our repair work is backed by a satisfaction guarantee, and the local pro performing the work is licensed and insured as their state requires. We stand behind the materials and the labor on the job we quote. If something isn’t right after the work is done, we want to hear about it.
Clear the area around the fireplace and make sure we can access the roof or the cleanout, and secure pets and any fragile items nearby. If you’ve noticed leaks, note where and when they appear, since that helps us trace the source. You don’t need to do anything else; the inspection and the estimate are on us.
Schedule Your Chimney Repair Service in Highland Creek Today
If your chimney is showing cracked mortar, water staining or a flashing leak, it’s worth having it looked at before the next wet season gets into it. Call (855) 337-1327 to book a free, no-obligation estimate in Highland Creek. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. You’ll get a camera inspection, a clear explanation of what we found, and a flat written price before any work begins.
Written by the team at Chimney Sweep Highland Creek.