Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Highland Creek Homeowners
Most Highland Creek chimneys don’t fail at the flue. They fail at the top. Water gets past a rusted-out cap or a fractured crown, runs down the masonry, and shows up months later as a stained ceiling, a spalled brick face, or a firebox that won’t draw. The cap and crown are the two parts that take the weather so the rest of your system doesn’t have to. Our technicians have up to 13 years of experience reading that damage and fixing the cause instead of patching the symptom. We install caps from Olympia Chimney and Copperfield, rebuild crowns with the right mortar mix, and seal them so water sheds where it should. Same-day visits are often possible in Highland Creek, and the estimate is always free. Call (855) 337-1327 to book a sweep or inspection.
What Our Chimney Cap & Crown Service Includes
A cap and a crown do different jobs. The cap sits on top of the flue and keeps rain, animals, and sparks out. The crown is the mortar cap across the top of the chimney itself, and it’s the part that directs water off the masonry. Fixing one without looking at the other is how homeowners end up back on the phone a season later. Here’s what each piece of the work covers.
Cap Installation
A chimney without a cap is open to everything: rain straight down the flue, birds and squirrels nesting on the smoke shelf, and sparks landing on the roof. We size and mount a new cap on the flue or flues, matching the footprint of your chimney so it looks like it belongs there. The cap is anchored so wind can’t walk it off, and we check the flue tile underneath before it goes on.

Cap Replacement
Old caps rust through at the seams, warp after a storm, or get knocked loose, and a loose cap does more harm than no cap because it can block the flue opening. We pull the old one, look at what caused it to fail, and set a replacement sized correctly for the flue. If the previous cap was the wrong size or type, we’ll tell you that plainly and fit the right one.

Crown Repair
Hairline cracks in the crown are common and mostly harmless; a crown that’s crumbling, pulling away from the flue tile, or letting water pool against the masonry is not. We cut out the failed mortar, rebuild the crown with a proper slope so water runs off, and tie it back to the flue properly. A well-built crown keeps water out of the brick and off the interior of the chimney.

Crown Coating
When a crown is sound but showing surface wear, a flexible coating buys it real time without rebuilding. We clean and prep the surface, then apply a coating that moves with the masonry instead of cracking away from it. This is a sensible option when the structure is intact and the repair is about protecting what’s already there.
Multi-Flue Cap
Chimneys with two or more flues need one cap that covers the whole top while still letting each flue breathe and draft properly. We build or fit multi-flue caps to the exact dimensions of your chimney top so the unit sits level and sheds water away from the crown. These are common on Highland Creek homes with a fireplace plus a furnace flue, and the fit matters more than the style.
Custom Cap
Oversized chimney tops, unusual flue arrangements, and masonry that doesn’t match standard sizes call for a custom cap. We measure the chimney on site and have the cap built to fit, including the animal screening and spark arrestor details that keep the opening functional. A custom-fit cap seals the top properly instead of leaving gaps that let water in at the edges.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with Olympia Chimney caps and components, and we know where their stainless models hold up and where the mounting hardware needs attention on older installations. Olympia makes a range of cap styles, and matching the right one to your flue size and roof profile is part of getting the job done properly. We also install Copperfield caps, which are a common choice for homeowners who want a sturdy, straightforward cap that handles weather without fuss.
For the crown side of the work, we use Famco materials where the job calls for a proven mortar and sealant approach, and we’ll bring in DuraFlex components when a cap or crown repair overlaps with relining work on the same chimney. Whether your chimney top has Olympia Chimney, Copperfield, Famco, or any other make on it, we can help. If you’re not sure what’s up there, that’s exactly what the inspection is for.
Signs You Need Chimney Cap & Crown Right Now
Most cap and crown problems give you warning. The trick is knowing what you’re looking at before the water gets inside the house.
- Water staining on the ceiling or chimney breast. A dark ring or a damp patch near the chimney usually means water is getting past the crown or a failed cap flashing. It won’t dry out on its own, and the longer it runs, the more masonry it soaks.
- Crumbling mortar at the top of the chimney. If the crown looks cracked, flaking, or separated from the flue tile, water is already working on it. Small cracks are worth watching; loose chunks are worth fixing now.
- Rust on the cap or a cap that’s sitting crooked. A rusted or tilted cap can let water in at the seams or block the flue opening. Both are cheap to fix compared to what a blocked flue does to your draft.
- Birds, squirrels, or debris in the firebox. An open or damaged cap gives animals a way in, and nesting material in the flue is a real fire risk. A properly screened cap closes that door.
- White staining or spalling on the brick below the crown. This is what water damage looks like on masonry: the brick face flakes or powders away. Catching it at the crown level saves the brickwork below.
Our Chimney Cap & Crown Process – Step by Step
- 1
We look at the whole top, not just the part you called about. A technician gets on the roof, photographs the cap, crown, flue tiles, and flashing, and checks how water is actually moving off the chimney. You see the photos before we recommend anything.
- 2
We explain what we found and what it means. You get a plain account of what’s failing, what’s holding up fine, and which repairs are urgent versus which can wait. No pressure to do everything at once.
- 3
We measure and match materials to the chimney. Cap size, crown slope, mortar type, and screening all get matched to your specific flue arrangement. This is where the right brand matters: Olympia Chimney or Copperfield caps for fit and durability, Famco materials for crown work, DuraFlex where the repair ties into relining.
- 4
We do the repair and show you the finished work. Old material comes off, the new cap or crown goes on, and we photograph the finished top so you can see the seal and the fit. If any part of the job turns out differently than expected once we’re up there, you hear about it before we continue.
- 5
We leave the top watertight and tell you when to look again. You get a clear sense of what to watch for and when the next inspection makes sense, usually tied to your burning season rather than a calendar sales pitch.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Highland Creek?
Chimney cap and crown work in Highland Creek typically runs from about $250 for a standard single-flue cap installation up to $1,800 or more for a full crown rebuild on a large or multi-flue chimney. A typical cap replacement runs $300 – $650 depending on cap size and material. Crown coating is usually $350 – $700. A multi-flue or custom cap generally lands between $600 and $1,200, and a crown rebuild with proper slope and flue-tile tie-in runs $900 – $1,800. These are estimates, not quotes; the written estimate you get after the inspection sets the final price.
What moves the number: the number of flues, the height and pitch of the roof, whether the crown needs a full rebuild or just coating, and whether the repair overlaps with liner work. How to avoid overpaying is simple: get the inspection first, ask to see the photos, and be suspicious of any recommendation that doesn’t come with visual evidence. Our free estimate includes the camera inspection and photo report, so you’re deciding on facts, not a sales pitch. If the crown can safely wait a season, we’ll say so.
Chimney Cap & Crown Near Highland Creek – Our Service Area
We serve Highland Creek and the surrounding neighborhoods, including Derita, NoDa, University City, Plaza Midwood, Elizabeth, Hickory Grove, Wesley Heights, Dilworth, Myers Park, Eastover, and Mountain Island. Drive times vary by location, but most of these areas are reachable the same day when you book early. If you’re in Derita or NoDa and want the same chimney cap & crown work we do here, we cover that too, and the chimney cap & crown page for NoDa has the local details. For the full picture of what we do across the area, start at Chimney Sweep Highland Creek.
Serving Highland Creek, NC – Our Local Coverage Area
We serve Highland Creek and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Highland Creek
A chimney cap is the cover that sits on top of the flue, and the crown is the mortar surface across the top of the chimney itself. The cap keeps rain, animals, and sparks out of the flue; the crown directs water off the masonry so it doesn’t soak into the brick. They work together, which is why we look at both during any inspection. Call (855) 337-1327 if you’re not sure what condition yours are in.
Most cap installations and replacements take one to two hours on site, while a crown rebuild usually takes most of a day because the mortar needs time to set properly. Coating work is faster, often under two hours. The exact time depends on roof access and how many flues are involved. We’ll give you a realistic window when we book, and the estimate is free.
Typical costs run from about $250 – $650 for a cap installation or replacement, $350 – $700 for crown coating, and $900 – $1,800 for a full crown rebuild, depending on size and flue count. Custom and multi-flue caps usually fall between $600 and $1,200. These are estimates; the written estimate sets the final price. Call (855) 337-1327 for an exact quote – estimates are free.
Yes. We install and service Olympia Chimney caps and know where their mounting hardware and screening tend to wear on older installations. We also work with Copperfield and Famco components, so we can match the right cap to your flue regardless of what’s there now. Whether you have Olympia Chimney or any other make, we can help.
Same-day visits are often possible in Highland Creek when you book early. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed Saturday. A call outside dispatch hours is booked into the next opening. Call (855) 337-1327 to check availability.
We stand behind the workmanship on cap and crown installations, and the materials we use carry their manufacturers’ warranties. If something we installed fails, we come back and make it right. The details are spelled out in your written estimate so there’s no ambiguity. Call (855) 337-1327 if you have questions about coverage on a specific repair.
Clear access to the fireplace and the roof area, and let us know about any roof hazards or skylights near the chimney. If you have prior inspection reports or photos, have them handy. Beyond that, you don’t need to do anything; the technician handles the rest. Call (855) 337-1327 to book and we’ll walk you through it.
Schedule Your Chimney Cap & Crown Service in Highland Creek Today
A cracked crown or a rusted cap is a small repair that protects a big investment. We’ll inspect the top, show you the photos, explain what we found, and give you a written estimate before any work starts. No obligation, no pressure. Call (855) 337-1327. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. For related work, see our chimney cap & crown overview.
Written by the team at Chimney Sweep Highland Creek.